Ana sayfa / Şablonlar / Benekli yavru kedi evi squishy

Hayvanlar

Benekli yavru kedi evi squishy

Şablonlar ve kılavuz güncellendi. İngilizce resimli kılavuzu izleyin. A4 veya Letter seçin ve %100 ölçekte yazdırın.

Benekli yavru kedi evi squishy
İndir

Şablon paketini indir

Şablonlar ve kılavuz güncellendi. İngilizce resimli kılavuzu izleyin. A4 veya Letter seçin ve %100 ölçekte yazdırın.

Kâğıt boyutunu seçin

Şablonlar ve montaj talimatları PDF biçimindedir. Görseller aşağıda ayrı olarak sunulur.
Bu materyal İngilizce olarak mevcuttur. ZIP, İngilizce dosyaları içerir.

Tek tek dosyalar
Zorluk: Orta Süre: 20–40 dk Tema: HayvanlarKâğıt: A4 / US Letter · 1 şablon dosyasıDosyalar: PNG / PDF / ZIPBaskı ölçeği: %100 / gerçek boyut3D model

Yazdırmadan önce dosyaları incele

Renkli şablonları, boyama sayfalarını ve kılavuzları incele. A4 veya US Letter PDF dosyasını gerçek boyutta yazdır.

Şablonlar ve kılavuz güncellendi. İngilizce resimli kılavuzu izleyin. A4 veya Letter seçin ve %100 ölçekte yazdırın.

Büyütmek için görsele tıkla. Her dosya için sunulan kâğıt boyutunda PDF seç.

Mevcut

Assembly guide 1 / 3 · English

Bu modelin resimli kılavuzu İngilizcedir. Aşağıdaki modele özgü Türkçe montaj adımlarını izleyin; parça harflerini ve işaretleri mevcut görsellerle eşleştirin.

Mevcut

Assembly guide 2 / 3 · English

Bu modelin resimli kılavuzu İngilizcedir. Aşağıdaki modele özgü Türkçe montaj adımlarını izleyin; parça harflerini ve işaretleri mevcut görsellerle eşleştirin.

Mevcut

Assembly guide 3 / 3 · English

Bu modelin resimli kılavuzu İngilizcedir. Aşağıdaki modele özgü Türkçe montaj adımlarını izleyin; parça harflerini ve işaretleri mevcut görsellerle eşleştirin.

Dosyadan kâğıt modele

Hangi dosyayı kullanmalıyım?

  1. 1
    Şablon ZIP dosyasını indir

    Bu materyal İngilizce olarak mevcuttur. ZIP, İngilizce dosyaları içerir.

  2. 2
    PDF indir

    PDF dosyasını belirtilen kâğıt boyutunda %100 / gerçek boyutta yazdır. Sayfaya sığdır seçeneğini kapat ve kesmeden önce ölçü işaretlerini kontrol et.

  3. 3
    Renkli şablon

    Renkli şablonu ekranda incele; yazdırmak için PDF kullan.

  4. 4
    Boyama şablonu

    Kâğıt düzken boya, ardından kes ve birleştir. Aynı sürümün bütün gerekli sayfalarını kullan.

Benekli yavru kedi evi squishy: Assembly guide 1 / 3 · English

Assembly guide 1 / 3 · English

Bu modelin resimli kılavuzu İngilizcedir. Aşağıdaki modele özgü Türkçe montaj adımlarını izleyin; parça harflerini ve işaretleri mevcut görsellerle eşleştirin.

Baskı ve montaj öncesi kontrol

  • 80–100 gsm paper, scissors, clear tape and a little soft filling. Print one size at 100%. Copy part letters to the back before cutting. Measure the 50 mm line before cutting. Use either the color or coloring sheets, not both. Cut solid outlines. Fold dashed lines only. Optional: cover the printed side with clear tape before cutting. Edges meet; do not overlap. Bridge each seam with clear tape on the outside. Use short pieces around curves and corners.

Temel adımlar

  1. STEP 1

    80–100 gsm paper, scissors, clear tape and a little soft filling. Print one size at 100%. Copy part letters to the back before cutting. Measure the 50 mm line before cutting. Use either the color or coloring sheets, not both. Cut solid outlines. Fold dashed lines only. Optional: cover the printed side with clear tape before cutting. Edges meet; do not overlap. Bridge each seam with clear tape on the outside. Use short pieces around curves and corners.

  2. STEP 2

    Cut A, R and K. The doorway is printed artwork: do not cut it out. K is a standing paper decoration. Fold only the dashed lines; keep both gables in the wall planes.

  3. STEP 3

    Fold the four walls of A into a rectangular ring. Match the free wall edges at the free corner and tape outside. Keep the attached floor hanging open.

  4. STEP 4

    Swing the floor up and tape its three free edges from below. Fold R along its center ridge and test it on both gables, then lift it off again. Do not glue the roof yet.

  5. STEP 5

    Add loose filling through the open roof. Keep both gables and all wall rims clear. Do not overfill; R must rest on the gables without pressure.

  6. STEP 6

    Place R over the two gables. Match the ridge and both eaves. Tape both eaves and all four sloping gable edges from outside. The roof has no hidden tabs.

  7. STEP 7

    Fold the 6 mm foot of K forward. Stand K against the printed door. Bridge each side edge of K to the house front with a short piece of clear tape on the outside, as highlighted. The foot rests on the table; do not tape it to the table. K stays flat and unfilled.

Sorun giderme

Assembly guide

Fold the 6 mm foot of K forward. Stand K against the printed door. Bridge each side edge of K to the house front with a short piece of clear tape on the outside, as highlighted. The foot rests on the table; do not tape it to the table. K stays flat and unfilled.

Benekli yavru kedi evi squishy: Türkçe montaj adımları

PDF dosyasını belirtilen kâğıt boyutunda %100 / gerçek boyutta yazdır. Sayfaya sığdır seçeneğini kapat ve kesmeden önce ölçü işaretlerini kontrol et.

1

80–100 gsm paper, scissors, clear tape and a little soft filling. Print one size at 100%. Copy part letters to the back before cutting. Measure the 50 mm line before cutting. Use either the color or coloring sheets, not both. Cut solid outlines. Fold dashed lines only. Optional: cover the printed side with clear tape before cutting. Edges meet; do not overlap. Bridge each seam with clear tape on the outside. Use short pieces around curves and corners.

2

Cut A, R and K. The doorway is printed artwork: do not cut it out. K is a standing paper decoration. Fold only the dashed lines; keep both gables in the wall planes.

3

Fold the four walls of A into a rectangular ring. Match the free wall edges at the free corner and tape outside. Keep the attached floor hanging open.

4

Swing the floor up and tape its three free edges from below. Fold R along its center ridge and test it on both gables, then lift it off again. Do not glue the roof yet.

5

Add loose filling through the open roof. Keep both gables and all wall rims clear. Do not overfill; R must rest on the gables without pressure.

6

Place R over the two gables. Match the ridge and both eaves. Tape both eaves and all four sloping gable edges from outside. The roof has no hidden tabs.

7

Fold the 6 mm foot of K forward. Stand K against the printed door. Bridge each side edge of K to the house front with a short piece of clear tape on the outside, as highlighted. The foot rests on the table; do not tape it to the table. K stays flat and unfilled.

Baskı ve montaj öncesi kontrol

  • 80–100 gsm paper, scissors, clear tape and a little soft filling. Print one size at 100%. Copy part letters to the back before cutting. Measure the 50 mm line before cutting. Use either the color or coloring sheets, not both. Cut solid outlines. Fold dashed lines only. Optional: cover the printed side with clear tape before cutting. Edges meet; do not overlap. Bridge each seam with clear tape on the outside. Use short pieces around curves and corners.

Sık sorulan sorular

PARTS

Measure the 50 mm line before cutting. Use either the color or coloring sheets, not both.

CLEAR TAPE · OUTSIDE

Edges meet; do not overlap. Bridge each seam with clear tape on the outside. Use short pieces around curves and corners.

A4 mü, US Letter mı?

Yazıcı kâğıdına uygun dosyayı seç ve %100 yazdır. Sayfalar arasında kâğıt boyutlarını karıştırma.

Önce boyayabilir miyim?

Evet. Kesmeden, bantlamadan ve birleştirmeden önce boya.

Resimli kılavuz Türkçe mi?

Sayfada modele özgü Türkçe montaj adımları bulunur. Mevcut resimli kılavuz İngilizcedir; parça harflerini ve işaretleri görsellerle eşleştirin.

Görsel önizleme