Gummy worms packet Paper Squishy

What you'll need

• Choose A4 or US Letter and print every sheet of either color or coloring templates, single-sided at 100%. Disable Fit to Page; check the 50 mm line. Color before cutting. Use scissors, paper glue, clear tape, soft filling and a blunt pressing tool. Cut solid outer lines; fold dashed lines. Printed decorations stay on the paper. Copy codes and marks 1-4 to the white backs.

Assembly overview

1. Cut the solid outer outlines; copy part codes and alignment marks onto the white backs first. A / front B / reverse Also keep G1a/b, G2a/b, G3a/b: three flat worms.
2. W1 carries 1 > 2 > 3. W2 carries 3 > 4 > 1. The small J flaps add overlap, not perimeter. A / B tabs | J = 8 mm overlap W1 end J1 goes UNDER start 3 of W2. A / B tabs | J = 8 mm overlap W2 end J2 goes UNDER start 1 of W1. Top view: both ends remain open Corner notches and tab-free zones above are copied from the cutting geometry. Keep them empty; do not add extra tabs.
3. The printed B outline is mirrored. Flip B left-to-right; its white back then matches the wall opening. A: printed face UP B: printed face visible B: white back UP UPPER TABS The white back of A rests on the upper tabs. Match all four marks before pressing. TURN OVER Copy the numbers to the back before cutting. Do not rotate B to force the edges to fit. LOWER TABS B stays printed side DOWN on the table. Lower tabs touch its white back.
4. Glue on the printed J flap; the white back of the next wall covers it up to the dashed stop line. FIRST JOIN: W1 J underneath W2 8 mm overlap Section: colours identify layers; thickness enlarged Glue on printed J. White back of W2 covers J. Folded shell: actual corner gaps Second join: W2 J2 underneath W1 start 1. Joined flat: W1 + W2; final J2 still free. J1 = wall mark 3. J2 = wall mark 1. Both cap openings stay accessible while these two joints set.
5. Fold BOTH rows inward. Glue the printed undersides of the lower tabs onto the white back of B. 1 / Align B below the wall B printed face DOWN Match 1-4. Keep the A opening clear for pressing. Enlarged section inside B: printed face DOWN 2 / Reach through A with a blunt tool. Press every lower tab while supporting B from beneath. Let dry. 3 / Fill lightly Leave the upper 5 mm and all top tabs clear. Do not pack tightly.
6. A rests ON the inward tabs. After A is attached, all remaining seam sealing is done from outside. Align all four marks Glue the upper tab faces, lower A onto them, and press gently around the rim. Enlarged section A: printed face UP glue on tabs Blue = clear tape crossing the OUTER seam. Keep the cap outside the walls. Clear tape crosses the outer seam onto BOTH surfaces. Check both rims and both J seams. Follow the next two detail pages before use.
7. Pale blue means clear tape. Every tape piece bridges the seam and contacts both mating surfaces. A / entire upper rim B / entire lower rim Turn the body over after A sets. Inspect the B perimeter from underneath. Cover every tab-free corner as well as the straight edges. J1 AND J2 / outside J1 at mark 3 J2 at mark 1 Run tape along each full vertical joint, across both wall faces.
8. Do not fill a designed notch with an invented tab. Exterior tape closes these small tab-free sections. Actual tab pattern / top view Enlarged cut geometry The enlarged notch is from this pattern. Tabs stop before the corner so they do not collide when folded. Tape sequence / enlarged 1 + 2: short strips on each edge. Fold their free halves down onto the wall. 3: a small overlapping bridge across the corner. Repeat on B. No inside access is needed.
9. White backs meet. The printed sides face outwards; these accessories stay flat and contain no stuffing. 1 / Matched printed halves 2 / Turn b over; glue WHITE back 3 / Align and press flat 6 cut halves = 3 flat worms. Keep them beside the packet. The front picture is printed artwork, not a cut-out window. Two paper layers / glue between white backs