Home / Templates / Paper airplane with a spinning propeller

Printable

Paper airplane with a spinning propeller Paper Squishy

An adult paper model with a hand-turned propeller, spring-fold landing gear and a soft rear compartment.

Paper airplane with a spinning propeller paper squishy preview
Download

Get the template pack

Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.

Choose your paper size

Template and guide
English

Individual file downloads
Difficulty: Hard Theme: Everyday Paper: A4 / US Letter File: PDF / WebP / ZIP Print scale: 100% 3D template
Printable templates

Assembly guide

Illustrations show the intended finished shape.

What you'll need

  • Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.
Assembly notes

Color template 1/3

Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.

Assembly notes

Color template 2/3

Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.

Assembly notes

Color template 3/3

Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.

Assembly notes

Coloring template 1/3

Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.

Assembly notes

Coloring template 2/3

Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.

Assembly notes

Coloring template 3/3

Print one set of colour or colouring sheets at 100%. Measure the 50 mm line. Use printer paper, clear tape, loose tissue, scissors and a ruler. Copy the IDs onto the backs. Cut black lines, fold dashes and align dots. Colour before taping.

Assembly overview

  1. For adults. Cut the slots in L/R and the holes in N/I/P. On D cut three sides of the hatch and crease its fourth side. Keep tape off bearings, sliding surfaces and spring folds.
  2. Fold S into an 8 × 4 mm tube. Tape its long butt seam. Centre it between the marks on W, 27 mm from each wingtip.
  3. Slide L and R onto W with the spar in the raised part of each slot. Insert H in the tail slots. Centre both wings, keep the sides 30 mm apart and tape the roots.
  4. Roll A along its 34 mm edge into a tube 30 mm long, about 3.5 mm across. Dry-fit P. Pass the shaft through N and I and turn it by hand. Before winding any stop permanently, dry-fit the full stack on A with N and I 13 mm apart. Mark both ends. I's triangle points up.
  5. From the nose the order is C1–P–C2–N–I–C3. Wind C2 and C3 to at least 5.5 mm across. Leave about 0.5 mm next to each bearing. Tape P to C1 so it turns with A.
  6. With the shell open, tape N at the nose and I on the forward marks. Align their holes using A. Tape K to the rear marks and T to the tail end.
  7. On each E leave the two 8 mm end pads flat and accordion-fold the middle. Tape the upper pad beneath W, under the spar, about 26 mm from the centre.
  8. Tape the lower pad at right angles to the top of J. Fold G into a 15 × 11 mm open tube. Slide it over J, tape its upper rim to W and keep the lower mouth clear.
  9. Fold O around the bottom of J and secure both wheel faces. Support the wing root and press and release each wheel separately. Check that J moves freely.
  10. Fit U and D from nose to tail. Press tape onto the top of K through the open bottom; reach its lower edge through the hatch. Fold V's feet apart and tape them to the rear centreline of U.
  11. Fold Z lightly into a V. Tape its 9 mm top pad under the tail, about 140 mm from the nose, and fold the foot aft. Rest the plane on its two main wheels and tail skid.
  12. Open the belly hatch behind K. Insert loose tissue only in the rear compartment. Keep the shaft and wheel mechanisms clear.
  13. Clear the hatch rim, fold the flap flush and overlap tape across all three cut edges. Turn the propeller and press each wheel before gently squeezing the rear compartment.

Image preview